© 2012 ATEÏSIDA8 & Ateis StudioUser ManualVersion 4
ATEIS - IDA810© 2012 ATEÏS...
ATEIS - IDA8100© 2012 ATEÏSA buzzing sound outputs to the monitoring speaker on the front panel of the IDA8C.Fault Handling:Update the firmware again.
Product Features 101© 2012 ATEÏSFault Indication:LED IndicatorWhen this error is detected, the following LEDs will light up:o G. Fault LED on the fron
ATEIS - IDA8102© 2012 ATEÏSA buzzing sound outputs to the monitoring speaker on the front panel of the IDA8C.Fault Handling:Amplifier Gain Too High
Product Features 103© 2012 ATEÏSAmplifier Gain Too Low
ATEIS - IDA8104© 2012 ATEÏSAmplifier Fail4.1.7.1.8 Line A/B ErrorFault Meaning:This error is mainly for loudspeakers connected to the IDA8C/S's
Product Features 105© 2012 ATEÏSIn the figure above, the difference in the percentage of Zone 4 is 78.24 which is greater than thetolerance of 15%, a
ATEIS - IDA8106© 2012 ATEÏSo Line A/B Bad Impedance:Text messages display at the touch screen on the front panel of the IDA8C:"Line A Error"
Product Features 107© 2012 ATEÏSLine A/B OpenLine A/B Bad Impedance
ATEIS - IDA8108© 2012 ATEÏSLine A/B Short4.1.7.1.9 Amplifier Line Leakage ErrorFault Meaning:An electricity leakage between the IDA8C/S and the speak
Product Features 109© 2012 ATEÏSA text message displays at the [Machine Fault Record] window in Ateis Studio:A buzzing sound outputs to the monitoring
Introduction 11© 2012 ATEÏS1 Introduction1.1 WelcomeThank you for choosing ATEÏS. We here at ATEÏS hope you will enjoy our technology as much as ween
ATEIS - IDA8110© 2012 ATEÏS"EVAC Input Error".A text message displays at the [Machine Fault Record] window in Ateis Studio:o EVAC Input Erro
Product Features 111© 2012 ATEÏSFault Handling : Evacuation Intput Error4.1.7.1.11 Local Ateis Net BrokenFault Meaning:The Local Ateis Net is broken,
ATEIS - IDA8112© 2012 ATEÏSFault HandlingCheck the wire connection between all IDA8C/S on the Local Ateis Net.If the wire connection is connected prop
Product Features 113© 2012 ATEÏSIf the fault is not solved, replace the Ateis Net card of the IDA8S.Once it's recovered, the LOG will show:"
ATEIS - IDA8114© 2012 ATEÏSA text message displays at the [Machine Fault Record] window in Ateis Studio:o Fireman Microphone Button Short:Text message
Product Features 115© 2012 ATEÏSA buzzing sound output to the monitoring speaker on the front panel of the IDA8C.Fault Handling:Observe the link and t
ATEIS - IDA8116© 2012 ATEÏS"Backup Device Offline." or"Operation Mode Fail."Text messages display at the window [Machine Fault Rec
Product Features 117© 2012 ATEÏSo G. Fault LED on the front panel of the IDA8C/S.Log:Text messages display at the touch screen of the IDA8C:"Remo
ATEIS - IDA8118© 2012 ATEÏSo PPM AS / PSS AS Capsule Microphone Short:Text messages display at the touch screen of IDA8C:"Remote Fault""
Product Features 119© 2012 ATEÏSo G. Fault LED on the front panel of the IDA8C/S.Log:o EVAC Input Error(Open):Text messages display on the touch scree
ATEIS - IDA812© 2012 ATEÏSHotelsRestaurantsShopping mallsTheme parksPlaces of worshipStadiumMuseumsIndustrialUniversity and campus applications
ATEIS - IDA8120© 2012 ATEÏSFault Handling : URGP Fault4.1.7.1.18 File CorruptionFault Meaning:The file CRC check code fails. (If the file monitoring
Product Features 121© 2012 ATEÏSFault HandlingReload the file.4.1.7.1.19 ModBus OfflineFault Meaning:The Modbus client can't communicate.Fault I
ATEIS - IDA8122© 2012 ATEÏS"Zone n BackUp AMP Rating too low" (where n = 1~8)Text messages display at the window [Machine Fault Record] in
Product Features 123© 2012 ATEÏS4.1.7.1.22 Local AteisNet Backup ModeFault Meaning:One of the local ATEIS net port has broken.Fault Indication:LED In
ATEIS - IDA8124© 2012 ATEÏSEthernet BrokenIf not, the IDA8 will enter in that mode only when the "Bypass Input line" on the rear pane
Product Features 125© 2012 ATEÏSA buzzing sound outputs to the monitoring speaker on the front panel of the IDA8C.Fault Handling:Check the trigger sou
ATEIS - IDA8126© 2012 ATEÏSo G. Fault LED on the front panel of the IDA8C/S.Log:Text messages display at the touch screen of the IDA8C:"Modan Off
Product Features 127© 2012 ATEÏS4.1.7.1.28 Normal AMP Out of TolerFault Meaning:The reference value measured from the normal amplifier is out of tole
ATEIS - IDA8128© 2012 ATEÏS"Zone n Backup AMP Gain Too Low " (Where n = 1~8)Text messages display at the window [Machine Fault Record] in At
Product Features 129© 2012 ATEÏSWhen the window [Monitoring(Matrix Mode)-IDA8C/S X ] appears, select the page [Zone Settings]:There are several fields
Introduction 13© 2012 ATEÏS1.3 EC Declaration of Conformity
ATEIS - IDA8130© 2012 ATEÏSMode:There are two types:1. 25V/70V/100VAn Audio signal through the amplifier and back to the IDA8C/S.2. 0dBInstead of goin
Product Features 131© 2012 ATEÏSBelow fields of the grid:Leakage Impedance:The impedance between the Line A/B +/- signal and ground causes the curren
ATEIS - IDA8132© 2012 ATEÏSLeakage occurrence:If the leakage impedance is lower than the leakage threshold which is defined in [Global Settings]tab,
Product Features 133© 2012 ATEÏS4.1.7.4 Normal Amplifier MonitoringSettings:First, in Ateis Studio, right click on the IDA8C/S block in the [Devices]
ATEIS - IDA8134© 2012 ATEÏSTo determine the boundary of the fault detection for a selected zone. There is a fault recognizedif one of the following co
Product Features 135© 2012 ATEÏSDisplays the value of measure, which is the gain of an amplifier.Faults:Amplifier Gain Too High:If Measure > (Unloa
ATEIS - IDA8136© 2012 ATEÏSWhen the window [Monitor(Matrix Mode) - IDA8C/S X] appears, select page [Backup AmplifierSettings]:Amplifier:In
Product Features 137© 2012 ATEÏSGet Reference:Gets the reference values of the selected zone for further fault detection. Be aware, the hardwareconfig
ATEIS - IDA8138© 2012 ATEÏSrecognized. Once this fault occurs, perform the following:o Make sure there is a good connection between the speaker and th
Product Features 139© 2012 ATEÏS4.1.7.6 Global SettingsThere are global settings listed below:Enable Monitor:A check box used to enable or disable the
ATEIS - IDA814© 2012 ATEÏS2 Safety DeclartionDo not expose the device to extreme temperatures, direct sunlight, humidity, or dust, which couldca
ATEIS - IDA8140© 2012 ATEÏS4.1.7.7 Tone SettingsIn the lower part of the window [Monitoring(Matrix Mode)-IDA8C/S X ], There is a page [Tone Settings]
Product Features 141© 2012 ATEÏSEnables 1K tone for monitoring. If this option is on, during the Start Time and the End Time, a1K tone signal will be
ATEIS - IDA8142© 2012 ATEÏS4.1.7.9 Open/Short CircuitOpen circuitAn open circuit occurs when a break exists in a complete conducting pathway.Once the
Product Features 143© 2012 ATEÏSThe following messages display on the touch panel of the IDA8C and in the Ateis Studio. See LineA/B Error.4.1.8 Log Li
ATEIS - IDA8144© 2012 ATEÏSLOG itemDescriptionI2C PCM3168 Driver ErrorI2C PCM3168 Compare ErrorI2C ADAPTER No ResponseI2C ADAPTER Driver ErrorI2C ADAP
Product Features 145© 2012 ATEÏSLOG itemDescriptionVoxnet OfflineModBus OnlineModBus OfflineModbus client connection statusLocal AteisNet Backup ModeL
ATEIS - IDA8146© 2012 ATEÏSLOG itemDescriptionZone n Line B OpenZone n Line B Short-OpenZone n Line B Bad Impedance(where n = 1~8)AMP Zone n No Leakag
Product Features 147© 2012 ATEÏSLOG itemDescriptionMajor Fault : xxx(where xxx = user customer define word)Major fault occurs form the "Fault Def
ATEIS - IDA8148© 2012 ATEÏSBypass mode input contact:Connect the pin CMD and pin GND of the bypass-mode input to a button. This input contact cantrigg
Product Features 149© 2012 ATEÏSUse Evacuation Input components.By using the Evacuation Input component, you can control the other logic components. T
Safety Declartion 15© 2012 ATEÏSTo prevent the unit from falling down and causing personal injury and/or property damage, avoidinstalling or mounting
ATEIS - IDA8150© 2012 ATEÏSUse the Logic Out component.By using the Logic Out component, you can output a signal coming from any logic compone
Product Features 151© 2012 ATEÏS1. Set your PC to a static IP address as 192.168.100.XXX (where the XXX is different from thedevice's default
ATEIS - IDA8152© 2012 ATEÏS4.2 Consoles and Accessories4.2.1 Redundancy Unit4.2.1.1 OverviewPAVA systems in very highly sensitive places like
Product Features 153© 2012 ATEÏSThere are three types of redundancy unit:RU-MAIN.: Switch digital audio and processing matrix like IDA8C, paging conso
ATEIS - IDA8154© 2012 ATEÏSmonitor input logic contacts P_WD and S_WD, The basic philosophy is that master RU monitor thesignal coming from primary an
Product Features 155© 2012 ATEÏSNote: Set RU-MAIN as M and RU-PDC/CTL as S on the back panel.Contact Outputs
ATEIS - IDA8156© 2012 ATEÏSFrom IDA8 to RU-CTL:IDA8: Contact outputs 1~8.RU-CTL: Output Contacts P_1~8, S_1~8. From RU-CTL to LED or signal output.RU-
Product Features 157© 2012 ATEÏSNormal Amplifier Input + Backup Amplifier InputNormal AMP input from IDA8 to RU-MAIN:IDA8: AMP Inputs Zone1~8. RU-MAIN
ATEIS - IDA8158© 2012 ATEÏS
Product Features 159© 2012 ATEÏSNormal Amplifier Output +Backup Amplifier OutputNormal AMP Output from IDA8 to RU-MAIN:IDA8: Zone1~8 AMP O.RU-MAIN: Zo
ATEIS - IDA816© 2012 ATEÏS2. Power up the device:Power up the IDA8C and make sure the power LED is on.3. Set the IP, Subnet mask and gateway address:S
ATEIS - IDA8160© 2012 ATEÏSSpeaker Zone Output
Product Features 161© 2012 ATEÏSFrom IDA8 to RU-MAIN:IDA8: Zone1~8, Lina a, Line b.RU-MAIN: Zone1~8, (P_LINE A, P_LINE B, S_LINE A, S_LINE B)From RU-M
ATEIS - IDA8162© 2012 ATEÏSRU-PDC: Configurable Audio I/O (CH_1~4)Telephone LinesFrom IDA8 to RU-PDC:IDA8: Line (Tel) Set.RU-PDC: Primary (IDA8 Tel.)
Product Features 163© 2012 ATEÏSRecordFrom RU-MAIN to Record device:RU-MAIN: Record_Out 1By-pass ModeSet a switch on IDA8's By-pass Mode input if
ATEIS - IDA8164© 2012 ATEÏSIDA8: By-pass Mode outputs.RU-MAIN: P_WD, S_WD (Watchdog)EVAC InputsFrom IDA8 to RU-CTL:IDA8: EVAC Inputs CH1~9.RU-CTL: EVA
Product Features 165© 2012 ATEÏSExternal Contact (usually on EVAC Inputs CH8)From IDA8 to RU-CTL:IDA8: EVAC Inputs CH8.RU-CTL: EVAC Inputs P_8, S_8.Fr
ATEIS - IDA8166© 2012 ATEÏSExpansion OutSet RU-MAIN as the master unit and RU-CTL/PDC as the slave unit.From RU-MAIN to RU-CTL/PDC:RU-MAIN: EXP_OutRU-
Product Features 167© 2012 ATEÏS4.2.1.3 ConfigurationThe following steps show how to configure redundancy system in IDA8 system:1. Setup H/W connectio
ATEIS - IDA8168© 2012 ATEÏSthen check if the device in [device list] grid is desired by it's serial number.5. Set Evacuation input Control Channe
Product Features 169© 2012 ATEÏS7. After this setting was finished, you can see the information on devices window show the two IDA8Care redundancy for
Quick Start 17© 2012 ATEÏSClick the [LOGIN] in the [SYSTEM SET MENU-1] page:Click the [USER NAME] in the [LOGIN] page:Input ID "ADMIN" which
ATEIS - IDA8170© 2012 ATEÏS8. Store one of redundancy systems, the other will store the same configuration automatically.9. There is a window shows th
Product Features 171© 2012 ATEÏS4.2.1.4 RU-Main4.2.1.4.1 OverviewRU-MAIN is a device for audio processor redundancy, the peripherals are connected wi
ATEIS - IDA8172© 2012 ATEÏSThis LED light up if primary audio processor is active. Primary Active Indicator:This LED light up if secondary audio proc
Product Features 173© 2012 ATEÏS Zone Amplifier Inputs:There are 8 sets of Zone Amplifier Input in RU-MAIN, each set consist of three connectors,
ATEIS - IDA8174© 2012 ATEÏSThere are two connectors of this output:PRI: Connect to Power Supply PRI connector next RU-MAIN/PDC/CTL.SEC: Connect to Pow
Product Features 175© 2012 ATEÏSS_BKP N: Connect to backup amplifier input of secondary audio processor.4.2.1.4.4 CharacteristicsDimension = 436mm x
ATEIS - IDA8176© 2012 ATEÏS4.2.1.5.2 Front Panel Secondary Active Indicator:This LED light up if active system is primary audio processor. Primary A
Product Features 177© 2012 ATEÏSRU-CTL is a device for audio processor redundancy, the peripherals are connected with RU-CTL notdirectly to audi
ATEIS - IDA8178© 2012 ATEÏS Expansion Power Supply:Output 24V DC power to next RU-MAIN/PDC/CTL devices.There are two connectors of this output:PRI: Co
Product Features 179© 2012 ATEÏS P_WD(Primary Watching Dog):RU devices monitor this logic signal for determining active audio processor, please r
ATEIS - IDA818© 2012 ATEÏSA page appears showing the message "Login successful".Go back to the [SYSTEM SET MENU-2] page and click the [ETHER
ATEIS - IDA8180© 2012 ATEÏS4.2.2.3 InstallationInstall the DNM device to the position in which you want the DNM to sense background noise and adjustlo
Product Features 181© 2012 ATEÏS3. One zone connects many loudspeakers, and the installation of loudspeakers are irregular but thedistance of all loud
ATEIS - IDA8182© 2012 ATEÏSbroadcast clearly, as all of the loudspeakers are connected from same source (same zoneoutput). Maybe the volu
Product Features 183© 2012 ATEÏSItemVoltageCurrent ConsumptionCommentDC Input18V~26V, Typical 24V250mA-Microphone:Sensitivity adjustment rang ... (60
ATEIS - IDA8184© 2012 ATEÏS5. A window [Remote Plug-In] pop up. Select RS485 port number and Remote Type, and key in theseries number which can b
Product Features 185© 2012 ATEÏS7. Double click the IDA8C/S to open DSP component editing window, then drag and drop to create"DNM"
ATEIS - IDA8186© 2012 ATEÏS9. To assign the DNM component to device. 10.Store the configuration, and then online.11.Click "DNM" component
Product Features 187© 2012 ATEÏS12.After the calibration is successful, the green LED will light up, and the DNM will start to work.13.If the White No
ATEIS - IDA8188© 2012 ATEÏS14.If the White Noise Level goes down to -40dB and the over LED is lighted up, this means thecalibration
Product Features 189© 2012 ATEÏS4.2.2.6 Operation NoticeOnce the calibration is successful, don't adjust the level in the rear of DNM component (
Quick Start 19© 2012 ATEÏS You need to reboot device to apply the settings.4. Install the Ateis Studio.5. Run the Ateis Studio.6. Network settings of
ATEIS - IDA8190© 2012 ATEÏS2. After plug-in successfully. These two DNM units are listed in the grids and showing their firmwareversion.3. In the
Product Features 191© 2012 ATEÏS4. To assign the DNM component to device.
ATEIS - IDA8192© 2012 ATEÏS5. Draw DSP DNM component, and connect the input and output.6. To modify the DSP component name. You can simply use propert
Product Features 193© 2012 ATEÏS7. Go to device editing window. Double click the device DNM component to open a window, and Linkdevice DNM componen
ATEIS - IDA8194© 2012 ATEÏS4.2.3 PPM AS4.2.3.1 OverviewUnidirectional Condenser Addressable Microphone, compatible with all system units, PPM AS uses
Product Features 195© 2012 ATEÏS4.2.3.2 Control Panel Microphone:The sleek condenser gooseneck microphone. This unidirectional condenser microph
ATEIS - IDA8196© 2012 ATEÏS EVAC LED:StatusFrequencyActivityPermanentSystem is under evacuation paging.Blinking ° ° PPM AS does not do a "Plug-
Product Features 197© 2012 ATEÏS4.2.3.3 Rear PanelThis chapter is about the adjustable volume on the PPM-AS's back panel and how to connect a key
ATEIS - IDA8198© 2012 ATEÏSThe keypad connector on the keypad for connecting the PPM-AS. Every keypad is shipped with oneflexible flat cable on it. Ke
Product Features 199© 2012 ATEÏSCreate PPM AS ObjectOpen or create a Ateis studio configuration file, in the [Device] design window, crea
Revision History Time Version 2012/07/23 1 Modified DNM chapter in the Product Features> Consoles and Accessories.The
ATEIS - IDA820© 2012 ATEÏSThere are three tabs at the right side of the window. Switch to the [Network] tab and open the drop-down list to select the
ATEIS - IDA8200© 2012 ATEÏSPin A~D of RS485 Input component is corresponds to PPM AS 1~4 audio plugged in PDC1~4respectively. Network Pagin
Product Features 201© 2012 ATEÏSNameThe name of PPM AS object.Rs485 TargetIndicates the connector on audio processor that PPM AS connected in the desi
ATEIS - IDA8202© 2012 ATEÏSPre-Announcement-NameThe name of pre-announcement message.Post-Announcement-EnabledEnable or disable post-announcement chim
Product Features 203© 2012 ATEÏSPathSpecify the directory to list all files with supported formats.File ListDisplay files in the directory Path.Displa
ATEIS - IDA8204© 2012 ATEÏSClear the list.o CloseClose the window.PPM AS SettingsDouble click the PPM AS object open the window of PPM AS Settings:Nam
Product Features 205© 2012 ATEÏSmore details.Remote Plug-inIt need to do a "Remote Plug-in" to make audio processor recognize this remote de
ATEIS - IDA8206© 2012 ATEÏS4.2.4 PSS AS4.2.4.1 OverviewThe PSS AS touch paging microphone console is a man-machine interface which allows paging cal
Product Features 207© 2012 ATEÏS4.2.4.2 Control Panel Microphone:A 280mm flex microphone. Power LED:This LED light up when the PSS AS is powered on. F
ATEIS - IDA8208© 2012 ATEÏSNo function for the moment. Right Button:Press and hold it for a while to calibrate touch screen. Monitoring Speaker:This e
Product Features 209© 2012 ATEÏSBandwidth @ -3dB = 200Hz ~ 12kHz.Maximum Cable Length100m on Category 5 cable4.2.4.4 ConfigurationTo make PPM AS work
Quick Start 21© 2012 ATEÏSAfter few seconds, all the Ateis devices in the LAN will be listed in a tree structure in the [Devices]field. Find the desir
ATEIS - IDA8210© 2012 ATEÏSPin A~D of RS485 Input component is corresponds to PPM AS 1~4 audio plugged in PDC1~4respectively. Network Pagin
Product Features 211© 2012 ATEÏSKeyRefer to the key on the page of PPM AS.Comment 1/2/3The text displayed on the key, there are three rows on it Comme
ATEIS - IDA8212© 2012 ATEÏSValueTo specify which code on integration paging event is bound with the key. AllSelect all zone for the key.Zone Selection
Product Features 213© 2012 ATEÏSEventSelect the event linked to.the key.Control ModeSpecify the control mode is Trigger or Control, see more details o
ATEIS - IDA8214© 2012 ATEÏSThis section is about setting up the message list for play on runtime in PSS AS. Before selection,you need to build chime l
Product Features 215© 2012 ATEÏSThis section is settings about chimes.Chime ListOpen a settings window to build up list of message for selection.Pre-a
ATEIS - IDA8216© 2012 ATEÏSAssign to Design ObjectsThe device object in design window needs map to physical device, then the configuration of t
Product Features 217© 2012 ATEÏS4.2.5.2 Control Panel OLED Display Exit Button:Back to the main menu. Knob:Turn: Select items or change volume.Press:
ATEIS - IDA8218© 2012 ATEÏS4.2.5.4 ConfigurationTo make URC AS work it need to edit configuration using Ateis Studio. Following sections are aboutc
Product Features 219© 2012 ATEÏSSerial NumberSerial number of the URC AS.NameName of the URC AS.MemoryIndicate memory usage of the URC AS for current
ATEIS - IDA822© 2012 ATEÏS9. Check the compatibility between the IDA8C and the Ateis Studio. Click [Read Version] in the menu.A window [Version] op
ATEIS - IDA8220© 2012 ATEÏSTextThe text in About text list.AddTo add a text in About text list.DeleteTo remove selected text from About text list.URC
Product Features 221© 2012 ATEÏSo Check boxes for selection of master/sub presets to be linked to the item.o Check All button to select all master/sub
ATEIS - IDA8222© 2012 ATEÏSItemIndex of the item.LabelThe display text of the item.Control TypeThe type of item. refer to prior section "Function
Product Features 223© 2012 ATEÏStopic Remote Plug-in for more details.Assign to Design ObjectsThe device object in design window needs map to physic
ATEIS - IDA8224© 2012 ATEÏS4.2.7 URGP4.2.7.1 OverviewThe URGP is an extension unit for the IDA8-System, LAPG2T and ECS. Each URGP provides thosesy
Product Features 225© 2012 ATEÏSStatusFrequencyActivityContinuousOne of the the fault inputs is active.One of the Evacuation inputs is Short Circuit o
ATEIS - IDA8226© 2012 ATEÏS RS232 Connector Evacuation Inputs:32 evacuation contact inputs for expanding the channels for IDA8 system. The following t
Product Features 227© 2012 ATEÏSItemVoltageCurrent ConsumptionCommentDC Input24VDC30mA-Maximum Cable LengthRS485 = 600m on Category 5 cableRS232 = 15m
ATEIS - IDA8228© 2012 ATEÏS4.2.8 CD-Touch4.2.8.1 OverviewCD-Touch Wall mounted cabinet remote paging console for Ateis audio processor.Wall-mount heav
Product Features 229© 2012 ATEÏS4.2.8.2 Control Panel1. Fireman Microphone HookAn U-shape hook to place fireman microphone.2. MicrophoneNot used.3. Po
Quick Start 23© 2012 ATEÏSA window [Device Select] opens. Select the IDA8 and click the [OK] button:A file manager opens. Select the IDA8 directory an
ATEIS - IDA8230© 2012 ATEÏS8. Left ButtonNo function for the moment.9. Middle ButtonNo function for the moment.10.Right ButtonNo function for the mome
Product Features 231© 2012 ATEÏSTHD @ 1kHz < 0.5%.Bandwidth @ -3dB = 50Hz ~ 20kHz.Maximum Cable Length100m on Category 5 cable4.2.8.4 Maintenance a
ATEIS - IDA8232© 2012 ATEÏS4.2.9 CD84.2.9.1 OverviewCD8 Wall mounted cabinet remote paging console for Ateis audio processor.Wall-mount heavy duty rem
Product Features 233© 2012 ATEÏS4.2.9.2 Control Panel1. Fireman Microphone HookAn U-shape hook to place fireman microphone.2. LED Test ButtonTest LED
ATEIS - IDA8234© 2012 ATEÏSThis embedded speaker to play chime when paging or monitor signal from audio processor, it needsto work with rs485 output
Product Features 235© 2012 ATEÏSTHD @ 1kHz < 1%.Bandwidth @ -3dB = 200Hz ~ 20kHz.Front Panel SpeakerImpedance = 8Ohm.Maximum Power @ 1kHz = 1W.THD
ATEIS - IDA8236© 2012 ATEÏS4.2.10 CD164.2.10.1 OverviewCD16 Wall mounted cabinet remote paging console for Ateis audio processor.Wall-mount heavy duty
Product Features 237© 2012 ATEÏS4.2.10.2 Control Panel1. Fireman Microphone HookAn U-shape hook to place fireman microphone.2. Busy Indicator(1~8)Show
ATEIS - IDA8238© 2012 ATEÏSprocessor.5. Fireman Microphone ConnectorDIN Connector for fireman microphone connection.6. Talk IndicatorThis LED light u
Product Features 239© 2012 ATEÏS4.2.10.3 CharacteristicsCaseDimension = 350mm (W) x 250mm (H) x 130mm (D).Weight = 4.7Kg.Color = RAL7016PowerItemVolta
ATEIS - IDA824© 2012 ATEÏSThe update is processing. When it's done, a window will pop-up asking to reboot the IDA8, click[Yes] to restart the
ATEIS - IDA8240© 2012 ATEÏSPlease use the Ateis Studio to check the paging console component is added correctly, and thenstore the table into the p
Product Features 241© 2012 ATEÏSSee more details in topic Fireman component.
ATEIS - IDA8242© 2012 ATEÏS4.2.12 CDPM4.2.12.1 OverviewCDPM Wall mounted cabinet remote paging console for Ateis audio processor. Wall-mount heavy dut
Product Features 243© 2012 ATEÏSAdditional RCA connectors with selection buttons support local audio injection for commercial usage.The RS485 communic
ATEIS - IDA8244© 2012 ATEÏSStatusFrequencyActivityPermanentThere are faults in audio processor.Blinking ° ° Lost communication with audio processor.
Product Features 245© 2012 ATEÏSColorStatusFrequencyActivityGreenPermanentThe zone only desired for paging is not using by othersources.15.Hold Indica
ATEIS - IDA8246© 2012 ATEÏS4.2.12.4 ConfigurationTo make CDPM work it need to edit configuration using Ateis Studio. Following sections are
Product Features 247© 2012 ATEÏSPin A~D of RS485 Input component is corresponds to CDPM 1~4 audio plugged in PDC1~4respectively. Network
ATEIS - IDA8248© 2012 ATEÏSNameThe name of CDPM object, click to rename.RS485 TargetIndicates the connector on audio processor that CDPM connected in
Product Features 249© 2012 ATEÏSPre-Announcement-EnabledEnable or disable pre-announcement chime playing.Pre-Announcement-NameThe name of pre-announce
Quick Start 25© 2012 ATEÏSCheck the device version using step 9 again, the version number should be in black which means it'snow compatible.11.Cr
ATEIS - IDA8250© 2012 ATEÏSPathSpecify the directory to list all files with supported formats.File ListDisplay files in the directory Path.DisplaySpec
Product Features 251© 2012 ATEÏSClear the list.o CloseClose the window.PPM AS SettingsDouble click the CDPM object open the window of PPM AS Settings:
ATEIS - IDA8252© 2012 ATEÏSmore details.Remote Plug-inIt need to do a "Remote Plug-in" to make audio processor recognize this remote devices
Product Features 253© 2012 ATEÏS4.2.13 PCP4.2.13.1 OverviewWall-mount heavy duty remote paging console with Access level 2 protection to comply with t
ATEIS - IDA8254© 2012 ATEÏSyet makes outlets easy to connect via a standard RJ45 connector.4.2.13.2 Control Panel1. A telephone styled microphone for
Product Features 255© 2012 ATEÏSStatusFrequencyActivityPermanentThere are faults in audio processor.Blinking ° ° Lost communication with audio proce
ATEIS - IDA8256© 2012 ATEÏS4.2.13.3 CharacteristicsCaseDimension = 346 mm (W) x 220 mm (H) x 128 mm (D).Weight = 3 Kg.Color = RAL7035.PowerItemVoltage
Product Features 257© 2012 ATEÏSDSP component configurationIt need to route audio from PCP to paging component for paging processing. See th
ATEIS - IDA8258© 2012 ATEÏSPPM AS ManagerPPM AS Manager is an unit of the software to manage settings about paging console that connectto audio proces
Product Features 259© 2012 ATEÏSKey-PriorityThe priority of key.Key-CountTo specify how many keys on PCP.Pre-Announcement-EnabledEnable or disable pre
ATEIS - IDA826© 2012 ATEÏSA window [Set Audio Module] opens. Click the [Create] button to continue.
ATEIS - IDA8260© 2012 ATEÏSPathSpecify the directory to list all files with supported formats.File ListDisplay files in the directory Path.DisplaySpec
Product Features 261© 2012 ATEÏSClear the list.o CloseClose the window.PPM AS SettingsDouble click the PCP object open the window of PPM AS Settings:N
ATEIS - IDA8262© 2012 ATEÏSdetails.Remote Plug-inIt need to do a "Remote Plug-in" to make audio processor recognize this remote devices. See
Product Features 263© 2012 ATEÏS4.2.14 PSC4.2.14.1 OverviewUnidirectional Condenser Addressable Microphone, compatible with all system units,
ATEIS - IDA8264© 2012 ATEÏS4.2.14.2 Control Panel Microphone:The sleek condenser gooseneck microphone. This unidirectional condenser microphone warran
Product Features 265© 2012 ATEÏSStatusFrequencyActivityPermanentThere are faults in audio processor.Blinking ° ° Lost communication with audio proce
ATEIS - IDA8266© 2012 ATEÏSDC Input18V~26V, Typical 24V150mA-Microphone Output:Maximum level = 6dBu.Output Impedance = 100Ohm.THD @ 1kHz < 0.1%.Ban
Product Features 267© 2012 ATEÏSDSP component configurationIt need to route audio from PSC to paging component for paging processing. See th
ATEIS - IDA8268© 2012 ATEÏSPPM AS ManagerPPM AS Manager is an unit of the software to manage settings about paging console that connectto audio proces
Product Features 269© 2012 ATEÏSKey-PriorityThe priority of key.Key-CountTo specify how many keys on PSC.Pre-Announcement-EnabledEnable or disable pre
Quick Start 27© 2012 ATEÏSA IDA8C block is created for further configuration as shown in the picture below:13.Add a Tone component and connect it to t
ATEIS - IDA8270© 2012 ATEÏSPathSpecify the directory to list all files with supported formats.File ListDisplay files in the directory Path.DisplaySpec
Product Features 271© 2012 ATEÏSClear the list.o CloseClose the window.PPM AS SettingsDouble click the PSC object open the window of PPM AS Settings:N
ATEIS - IDA8272© 2012 ATEÏSdetails.Remote Plug-inIt need to do a "Remote Plug-in" to make audio processor recognize this remote devices. See
Product Features 273© 2012 ATEÏS4.2.15 URC200 TPC4.2.15.1 OverviewThe URC200 is an programmable remote controller (TCP/IP) for the IDA8 system, LAPG
ATEIS - IDA8274© 2012 ATEÏS4.2.15.2 Control Panel TFT Panel:A color 2" TFT panel presents the menu system of URC 200 TPC. IR Receiver:It receives
Product Features 275© 2012 ATEÏSDiagonal = 2"Resolution = 176 x 220Power:ItemVoltageCurrent ConsumptionCommentDC Input18V~26V, Typical 24V50mA-Ma
ATEIS - IDA8276© 2012 ATEÏS3. Press button [Reset] to make the reset root menu to default.4. Click the button on field [Link] for the desired menu ite
Product Features 277© 2012 ATEÏS5. The default name is "Group 1", you can change it to the other string.6. Click buttons on the field [Link]
ATEIS - IDA8278© 2012 ATEÏS7. For example, I create two items: "increase" and "decrease" for controlling the audio level.8. Clink
Product Features 279© 2012 ATEÏSThe fields in the grid are described below:TypeTo indicate the communication protocol used, this field is read only.IP
ATEIS - IDA828© 2012 ATEÏS14.Compile and Store:Once the design is done, click [Compile All]. The Compiling window appears as shown in the picturebelow
ATEIS - IDA8280© 2012 ATEÏS4.2.15.4.2 Import/Export ConfigurationYou can export the URC200 TPC configuration to a file or import the file to restore
Product Features 281© 2012 ATEÏSAfter power up, you'll the a message on the top of LCD screen: "No Preset". It means the URC200 TPCnow
ATEIS - IDA8282© 2012 ATEÏS2. Click page [Remote Device]. This page lists all devices in the network. Press the button [Search] todiscovery URC200 TPC
Product Features 283© 2012 ATEÏS4. There is a box [Function List] at the right side of the window. By select the entry of the grid, the itemsinside th
ATEIS - IDA8284© 2012 ATEÏS4.2.15.5.2 Protected ModeThere are some internal settings of URC200 TPC. Those settings are in the protected mode menu. To
Product Features 285© 2012 ATEÏSVersion:This page displays the firmware version of URC200 TPC.S. B.:This page is comprised of two settings:Saver Time:
ATEIS - IDA8286© 2012 ATEÏSo SLAVE PPM: Connects to the JB for Slave PPM. Note: The Slave PPM shares the sameaudio output with the Master PPM and i
Product Features 287© 2012 ATEÏSWith several PPM and URC:1. Only the connection between the first JB and the audio processor transmits the audio. Yo
ATEIS - IDA8288© 2012 ATEÏS4. Switch the PPM Master/Slave selection correctly otherwise the PPM AS cannot be identifiedin Ateis Studio. See the pictur
Product Features 289© 2012 ATEÏS4.2.16.3 RJ45RJ45 pin outFor practically all the wiring you'll need straight CAT5 FTP OR STP cable (4 pairs):o Pi
Quick Start 29© 2012 ATEÏSThen, click [Store All] to store your design into the IDA8. The Store window appears as shown in thepicture below.Meanwhile,
ATEIS - IDA8290© 2012 ATEÏSWith PPM, a straight CAT5 FTP cable 5 pairs is needed (provided with PPM):o Pin1 = Slave RS-485 Ao Pin2 = 24VDCo Pin3 = Mas
Product Features 291© 2012 ATEÏS4.2.17 PPM-IT54.2.17.1 OverviewThe PPMIT5 IP paging console is a man-machine interface which allows call-pa
ATEIS - IDA8292© 2012 ATEÏSAll the settings are done through web pages with your favorite web browser. Thanks to powerful echocancellation, the PP
Product Features 293© 2012 ATEÏS Power LED:This LED light up when the PPM-IT5 is powered on. Fault LED:To display fault status of system, permanen
ATEIS - IDA8294© 2012 ATEÏS Primary horizontal menu:MAIN: Display the Device as button, Events as buttons and function buttons.DIAL: For typing teleph
Product Features 295© 2012 ATEÏS Back to root menu (works with Macro buttons) Select all. Deselect all. Page Up/ Page Down.4.2.17.3.1 MainButton type
ATEIS - IDA8296© 2012 ATEÏSPaging Group (Orange) : The Paging Group button. Press it then start paging by speaking to thegoose-neck microphone of the
Product Features 297© 2012 ATEÏSThe Call from other device (one to one):
ATEIS - IDA8298© 2012 ATEÏSPaging to multi-user:
Product Features 299© 2012 ATEÏS4.2.17.3.2 DialBS: Backspace.CANC: Cancel all. CAPS: Caps lock.After entering a number, press the phone icon " &
3Contents3© 2012 ATEÏSTable of ContentsIntroduction 11...
ATEIS - IDA830© 2012 ATEÏS15.Adjust element:Set the element of the Tone Generator:Level(dB) = -10Tone Button = OnTone freq.(Hz) = 2.00kNow you can see
ATEIS - IDA8300© 2012 ATEÏS4.2.17.3.3 MessagePlay messages: Select the audio file > Go to Main page, select devices > Press button.The audio
Product Features 301© 2012 ATEÏSUse - , + buttons to adjust the speaker volume.4.2.17.4 CharacteristicsCaseDimension = 250mm(W) x 140mm(L) x 80mm(H)We
ATEIS - IDA8302© 2012 ATEÏS4.2.17.5 Maintenance and TroubleshootingThis chapter will help you to diagnose the common problems for troubleshooting and
Product Features 303© 2012 ATEÏSSPA 2240The SPA were specifically developed to meet the requirements of EN 60849 for safety installations.Eac
ATEIS - IDA8304© 2012 ATEÏSInput impedance: 22k ohm4.3.1.2 Front Panel VU Meter:The VU-meter is composed of three LEDs that represent three differe
Product Features 305© 2012 ATEÏS4.3.1.3 Rear Panel Fuse Receptacles:Two fuse receptacles are located on the left of the amplifier’s rear panel. Power
ATEIS - IDA8306© 2012 ATEÏSFor each channel, there is an XLR balanced input and a Euro-terminal block balanced input. Eachinput can be gain adjusted
Product Features 307© 2012 ATEÏSPower:ItemVoltagePower ConsumptionCommentAC Input230V +/- 10%SPA2120Standby: 28WFrequency:47Hz~63HzIdle: 150WPmax: 322
ATEIS - IDA8308© 2012 ATEÏS4.3.1.5 Parallel OutputHere we can combine 2 or more channels into one. For example, 60W x 2 Channels to be one channelwith
System Functionality 309© 2012 ATEÏS5 System Functionality5.1 Ateis Studio5.1.1 Overiew of Ateis StudioAteis Studio allows complete audio systems
Quick Start 31© 2012 ATEÏS4 Product Features4.1 IDA8 Series Audio ProcessorThe IDA8 is a third generation modular system that complies with
ATEIS - IDA8310© 2012 ATEÏSIn addition you will find a comprehensive selection of tools for system design and programming using ourAteis Studio integr
System Functionality 311© 2012 ATEÏS5.1.3 Install Ateis StudioPlease follow the steps below to install Ateis Studio:1. Before installing the Ateïs Stu
ATEIS - IDA8312© 2012 ATEÏSClick [Next]5. Type in a user name and your organization name if you want and click [Next]
System Functionality 313© 2012 ATEÏS6. By default the program software is installed under the path "C:\Program Files\ATEIS\ATEIS Studio vx.x.x.x&
ATEIS - IDA8314© 2012 ATEÏS8. Wait until the end of the installation.9. After all installation tasks have been finished successfully click [Finish] to
System Functionality 315© 2012 ATEÏS10.The installation program creates a shortcut to the "ATEIS Studio v.1.x.x .exe" named "ATEIS Stud
ATEIS - IDA8316© 2012 ATEÏS5.1.4 Windows LayoutThe basic windows layout should look like the figure showed above, however, the layout can be changedif
System Functionality 317© 2012 ATEÏS7. Status Bar:Displays the status of software including the modification indication of editing file, mouse cu
ATEIS - IDA8318© 2012 ATEÏS5.1.6 EditSelect All :o Select all the components and wires.SelectSelect All DSP Components :o Select all DSP components
System Functionality 319© 2012 ATEÏS5.1.7 ViewEach item in the [View] menu can open a specific window to perform settings modification
ATEIS - IDA832© 2012 ATEÏS4.1.1 IDA8C4.1.1.1 OverviewThe IDA8C Controller unit enables operators to see a detailed overview of the operational status
ATEIS - IDA8320© 2012 ATEÏSProperties :Opens the window of Properties which allows you to inspect various parameters of an object ingraphic
System Functionality 321© 2012 ATEÏSZoom in to the graphic editor.Zoom Out :Zoom out of the graphic editor.Zoom Original :Zoom to the original size
ATEIS - IDA8322© 2012 ATEÏSEnables or disables moving an object by multiple pixels at a time.Layer:o Add Layer :Adds a layer of the graphic editor.o
System Functionality 323© 2012 ATEÏS5.1.9 Component EditingPosition OperationPosition Operation Type Some functions, as Alignment or Pack use a refere
ATEIS - IDA8324© 2012 ATEÏSo Reference Component In Reference Component mode, the reference is a component. If you select severalcomponent
System Functionality 325© 2012 ATEÏSAlignment You can select several elements (by maintaining a left click and moving the mouse you will havea select
ATEIS - IDA8326© 2012 ATEÏSYou can select several elements (by maintaining a left click and moving the mouse you will havea selection square) and then
System Functionality 327© 2012 ATEÏSYou can select several components (by maintaining a left click and moving the mouse you willhave a selection squar
ATEIS - IDA8328© 2012 ATEÏSRight Angle Select Right Angle if you want to draw the wire only with right angles (90 degrees).Auto Corner Select Auto Cor
System Functionality 329© 2012 ATEÏSSignal Path Temporary In this mode, by selecting a signal link, the signal link and the entire signal path linked
Product Features 33© 2012 ATEÏSAlso, The IDA8 have two detection functions. Short-to-ground: Speaker line to ground detection andShort-circuit
ATEIS - IDA8330© 2012 ATEÏSSignal Path Lock In this mode, by selecting a signal link, the signal link and the entire signal path linked will behighlig
System Functionality 331© 2012 ATEÏS5.1.10 ToolsBy changing the skin you can modify the global style (color and appearance) of the windows. You cancho
ATEIS - IDA8332© 2012 ATEÏSMc Skin
System Functionality 333© 2012 ATEÏSLondon Liquid Sky
ATEIS - IDA8334© 2012 ATEÏS5.1.11 OperationIn this menu you will find the major operations related to system connection allowing you to compile thecon
System Functionality 335© 2012 ATEÏSMaster Preset SelectorThe drop-down list of "Master Preset" allows the user to switch master presets.Mas
ATEIS - IDA8336© 2012 ATEÏSIn this topic you will find tools to re-arrange windows or find hidden opened windows.Close Close the opened active window.
System Functionality 337© 2012 ATEÏSIn the bottom of the window menu, you will find all the opened windows of your project. By selectingof the windows
ATEIS - IDA8338© 2012 ATEÏSOn the left is a component template and on the right is the design window. There are three pages ofcomponent templates,
System Functionality 339© 2012 ATEÏS5.1.15 Resource ManagerResource manager is a container for files which can be used in a device configuration. Sec
ATEIS - IDA834© 2012 ATEÏSThis LED lights up when a global fault is detected.Note: Fault LED and system fault LED are exclusive. If system fault and g
ATEIS - IDA8340© 2012 ATEÏSDeleteRemove selected files from the resource manager.ExportExport selected files to a single resource packed file.ImportIm
System Functionality 341© 2012 ATEÏSCurrentIndicates which layer is the current layer. The newly created objects will be put into the currentl
ATEIS - IDA8342© 2012 ATEÏS5.1.19 PropertiesProperties window allows users to browse/edit settings of the selected objects in the design window. Bycli
System Functionality 343© 2012 ATEÏS5.1.20 Message LibraryMessage Library provides an easy interface to manage messages used in Ateis Studio. By click
ATEIS - IDA8344© 2012 ATEÏS5.1.21 Logo LibraryLogo Library is a settings windows for Logo Library management. By clicking the menu [View > LogoLi
System Functionality 345© 2012 ATEÏS5.2.2 Master PresetsThe Master Preset function allows switching between several designs on the same device. Each M
ATEIS - IDA8346© 2012 ATEÏSMaster Preset NameThe name of the master preset.EditBy clicking the ellipsis cell in the grid you can open the DSP design w
System Functionality 347© 2012 ATEÏSRemoveTo remove a selected master preset.Master Preset SwitchingThere is only one master preset active at a ti
ATEIS - IDA8348© 2012 ATEÏSMaster Preset Combo BoxBy clicking this combo box, you can switch to the desired master preset and then edit the sub-preset
System Functionality 349© 2012 ATEÏSTable of linked elementsThis table lists all elements controlled by the sub-preset. On the right there is a small
Product Features 35© 2012 ATEÏSLine A ErrorLine B ErrorBackup AMP ErrorAMP Line Leakage Error EVAC Reset Button:Cancels the event triggered by EVAC bu
ATEIS - IDA8350© 2012 ATEÏS5.3 Event Management5.3.1 Event ManagerThere are various types of events for controlling Ateis devices. For example
System Functionality 351© 2012 ATEÏSAdds an event to the event manager, Some event cannot be created in this window, such as apaging event. In this
ATEIS - IDA8352© 2012 ATEÏSname of the event. The following figure is an example:Next, a window which displays brief information of the relationship b
System Functionality 353© 2012 ATEÏSState Pages:There is a page for each state in the value trigger event. To switch states, click the tab of thedesir
ATEIS - IDA8354© 2012 ATEÏSClick the [Add] button to create a new event. A second window will open prompting you to choosewhich kind of event is desir
System Functionality 355© 2012 ATEÏSOn the right side of window, there is a knob to simulate the source that triggers the event. If youadjust the kn
ATEIS - IDA8356© 2012 ATEÏSClose:Closes the settings window.5.3.4 Step Trigger EventDescription:This event is used to control the element value. It ad
System Functionality 357© 2012 ATEÏSNext, a window shows the brief information. Select the check box at the row "All":Click the [Content] fi
ATEIS - IDA8358© 2012 ATEÏSState PagesThere is a page for each state in the step trigger event. To switch states, click the tab of thedesired state.
System Functionality 359© 2012 ATEÏSClick the [Add] button to create a new event. A second window opens prompting you to choosewhich kind of event
ATEIS - IDA836© 2012 ATEÏSTwo backup amplifier connectors included 0 dB to amplifiers and 100V return from amplifiers. Amplifier Zone Outputs:8 Zone 0
ATEIS - IDA8360© 2012 ATEÏSElement:Indicates which element of the component is controlled by the value trigger.Component:Indicates which component of
System Functionality 361© 2012 ATEÏSClick the [Add] button to create a new event, a second window opens prompting you to choosewhich kind of even
ATEIS - IDA8362© 2012 ATEÏSClick the [Add] button to create a new event, a second window opens prompting you to choosewhich kind of event is desi
System Functionality 363© 2012 ATEÏS5.4 Device ManagementDevice Management window helps the user to search Ateis devices in the network. You can modif
ATEIS - IDA8364© 2012 ATEÏSName:The object of the design window that corresponds to the device. After the relation of the objectand device is created,
System Functionality 365© 2012 ATEÏS3. Select the desired device and click the "Connect" at the device function area and the connectionstart
ATEIS - IDA8366© 2012 ATEÏSClick the [Read] button to get the version data from the device.Firmware Unit:The firmware program unit in the device.Compa
System Functionality 367© 2012 ATEÏS2. Search and Connect to the device which needs updating. For step by step guide, see "DeviceM
ATEIS - IDA8368© 2012 ATEÏSThe progress bar in the Update window displays the status of the update:6. When the update is completed, a pop-up window wi
System Functionality 369© 2012 ATEÏS7. Now your device is updated. Since the device is rebooted, it is currently unconnected. Select it andclick [Con
Product Features 37© 2012 ATEÏS Telephone Connector:A connector for external telephone connection.(optional). Bypass Mode Outputs:This port is used to
ATEIS - IDA8370© 2012 ATEÏS5.4.4 Ateis Net DeployingThis function allows the user to configure the networking state of devices on Ateis Net. Connectin
System Functionality 371© 2012 ATEÏS5. The LED of Audio Processor indicates while deploying. The Data LED blinks for a while and turns tocontinuous li
ATEIS - IDA8372© 2012 ATEÏS5.4.5 Remote Plug-inThis function is used to register remotes to an audio processor. When the remote is for first time used
System Functionality 373© 2012 ATEÏSThe internal identification for each remote device.Remote Type:Specifies which type of remote device belong to the
ATEIS - IDA8374© 2012 ATEÏS5. If you have many remotes to be plugged-in, you need to manually key in the SN for Ateis Studio toassigned the IDs.Selec
System Functionality 375© 2012 ATEÏS5.4.6 ReverseThis function allows the user to reverse designs from audio processors.1. Open the Device Management
ATEIS - IDA8376© 2012 ATEÏSdesign.5.4.7 Machine File SystemThis function allows you to manage the audio files stored in the devices.1. Open the Device
System Functionality 377© 2012 ATEÏSThe left grid lists the files under the specific folder in your PC, and the right grid is for the device.All: Sele
ATEIS - IDA8378© 2012 ATEÏSImport: Imports an Ateis Studio .zip file. Ateis Studio will automatically recognize the format andput the files under the
System Functionality 379© 2012 ATEÏS4. You can also click the [Remote Update] to open the setting window and open the drop-down list toselect the remo
ATEIS - IDA838© 2012 ATEÏSPower:ItemVoltageCurrent ConsumptionCommentAC Input100V~240V1.6A@100V, 0.7A@240VFrequency:47Hz~63HzDC Input18V~26V, Typical
ATEIS - IDA8380© 2012 ATEÏSIf not, click the [...] to browse the files for updating as shown in the picture below:In case of adding files from other d
System Functionality 381© 2012 ATEÏS5.4.9 Chime Data StoreThis function allows you to store the chime into the remote devices connected with the Audio
ATEIS - IDA8382© 2012 ATEÏSBasically, the files will automatically read by Ateis Studio if they're placed under the right directory.If not, click
System Functionality 383© 2012 ATEÏS7. The Updating procedure will take a few minutes and once it's done, the Updated status shows"Succeed&q
ATEIS - IDA8384© 2012 ATEÏS4. Set the read count and click the [Refresh] button to show the log. In case of sending the log to yourtechnician, click t
System Functionality 385© 2012 ATEÏS3. Click [Log] to open the log window.4. Here you can read the Time set in the device and manually adjust the time
ATEIS - IDA8386© 2012 ATEÏS5. In case of using the daylight saving time, switch to the Daylight Saving tab to set.5.4.12 VR CalibrationThis function i
System Functionality 387© 2012 ATEÏS2. Search and Connect to the device. For step by step guide, see "Device Management > Search andConnect &
ATEIS - IDA8388© 2012 ATEÏS4. Follow the steps 1-4 to perform the store. You can store two images into many URC AS units a time.Once it's done th
System Functionality 389© 2012 ATEÏS5.4.14 Fault E-mail SettingThis function allows the user to receive fault reports from the IDA8 by the E-mail in t
Product Features 39© 2012 ATEÏSSensitivityMinimumMaximumUnitFrequency0dBu-0.04%20~20kHz@+4dBu-12dBu-0.06%[email protected]%20~20kHz@-14dBu-40d
ATEIS - IDA8390© 2012 ATEÏS
System Functionality 391© 2012 ATEÏSServer IP: Enter the Mail Server.Server Port:SMTP port of the Mail Server. The default value is 25.Sender: The sen
ATEIS - IDA8392© 2012 ATEÏSCheck the checkbox of the faults you want to receive.4. Once the E-mail setting is done, the mail sent by the device contai
System Functionality 393© 2012 ATEÏS5.4.15 ModbusThis function allows the user to set the Modbus message priorities and schedule Interval.1. Open the
ATEIS - IDA8394© 2012 ATEÏSEnable: Enables the Priority/Lock setting.Priority: Shows the default priority, click to set the message priority for Modbu
System Functionality 395© 2012 ATEÏS00:10:00. Then, the Schedule is first-time triggered at 07: 00: 00 and will be triggered 10minutes later after t
ATEIS - IDA8396© 2012 ATEÏSrebooted and click [Reset] to reboot them. 5.4.17 RedundancyThis function allows the user to set the Redundancy system used
System Functionality 397© 2012 ATEÏSEvac Input Control Channel: The channel which is connected to the Redundancy Units.Device List: Shows how many uni
ATEIS - IDA8398© 2012 ATEÏS5.4.19 TelePhone Card SettingThis function allows the user to monitor the ethernet status.1. Open the Device Management Win
System Functionality 399© 2012 ATEÏSAfter the assignment is completed, you will receive a preview of the string used to control the Ateisdevices
ATEIS - IDA84© 2012 ATEÏS...
ATEIS - IDA840© 2012 ATEÏSBandwidth = 20Hz ~ 20kHzPDC:Maximum Output Level = 10 dBuOutput Impedance = 300 OhmTHD @ 1kHz at output < 0.02Bandwidth @
ATEIS - IDA8400© 2012 ATEÏSDevice Name of GridLists the element containing the component.5.5.1.4 3rd Party Control CommandThis window shows a preview
System Functionality 401© 2012 ATEÏSThere are two pages in the window:User LevelsA user level is a combination of user privileges where in a privilege
ATEIS - IDA8402© 2012 ATEÏSOn top of window, there is a grid list all user levels including four defaults. Each column represents anaction authority.
System Functionality 403© 2012 ATEÏSnot allowed to remove.5.6.3 User AccountsAteis devices allow the creation of multiple users for controlling a syst
ATEIS - IDA8404© 2012 ATEÏS6 Components of Audio Processor6.1 AEC6.1.1 ParametersThis component is used to avoid reflected signals caused by acoustic
Components of Audio Processor 405© 2012 ATEÏSAEC ParametersParameterRangeCommentEcho Detectled This led is lit when an echo is detected.Signalled This
ATEIS - IDA8406© 2012 ATEÏSParameterRangeCommentResetButtonResets the echo cancellation on the channelFar-EndVolume Vu-meter(dB)Audio volume of the fa
Components of Audio Processor 407© 2012 ATEÏSAEC Coefficient / Reset On each channel you can independently activate the echo cancellation process by s
ATEIS - IDA8408© 2012 ATEÏSrespectively.If you want to modify the volume of a source (near-end inputs) use the "Near-End Level" knobs in the
Components of Audio Processor 409© 2012 ATEÏSThe NLP threshold parameter is not available, the threshold is now automatically set.6.2 Delay (Advanced)
Product Features 41© 2012 ATEÏSContact OutputContact FormMaximumUnitCarry Current1.0ADCMaximum Voltage100VDCElectrical Life1 x 10^8 (Ref 10VDC, 10mA)-
ATEIS - IDA8410© 2012 ATEÏSDelays the audio signal input to the component. The delayed component records the audio into ainternal buffer and then pl
Components of Audio Processor 411© 2012 ATEÏSTypeMaximum5ms5 µs50ms20 µs100ms20 µs200ms20 µs500ms20 µs1000ms20 µs2000ms20 µs*3: The maximum value of D
ATEIS - IDA8412© 2012 ATEÏSImagine a conference in a large room. Normally speakers are placed beside the people speaking, solisteners at the end of
Components of Audio Processor 413© 2012 ATEÏS6.3 Delay (Basic)Component Template:Component Appearance:Description:Delays the audio signal input to
ATEIS - IDA8414© 2012 ATEÏS(Advanced) that is not allowed to mute or bypass the signal of the input. There are two ways toadjust the delay time
Components of Audio Processor 415© 2012 ATEÏSTypeMaximum1000ms20 µs2000ms20 µs*3: The maximum value of Distance depends on the type of Delay (Basic)Ty
ATEIS - IDA8416© 2012 ATEÏS6.4 Dynamic6.4.1 AGC\AGC StereoComponent Template:Component Appearance:Description:With this Automatic Gain Control(AGC), t
Components of Audio Processor 417© 2012 ATEÏSThe control window of AGC Stereo is the same as the AGC's.Element Properties:NameInitialMinimumMaxim
ATEIS - IDA8418© 2012 ATEÏSDetermines the maximum of automatic gain. Limit the max gain to keep a natural audio dynamic.Attack Time:Adjusts the fade-i
Components of Audio Processor 419© 2012 ATEÏSThreshold: Set at -25dB. The level is adjusted only when the input signal is above -25dB. This is tokeep
ATEIS - IDA842© 2012 ATEÏSDeviceConnectionMax. NumFunctionCD TouchPDC1Wall mounted cabinet remote paging console with touch screenand Fireman Micropho
ATEIS - IDA8420© 2012 ATEÏS6.4.2 Auto Noise Gain (A.N.G)Component Template:Component Appearance:S.M.: Sensing Microphone input.P.M.: Program Material
Components of Audio Processor 421© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitMin Gain-6.0-15.000.1dBMax Gain6.0015.00.1dBSamp
ATEIS - IDA8422© 2012 ATEÏSItem list of Response Speed:No.Name1Low2Medium3HighElement Description:Min Gain:The minimum level compensation.Max Gain:The
Components of Audio Processor 423© 2012 ATEÏSIt means the speed of adapting the P.M. audio level depends on the ambient noise.Paging Activity:Lights u
ATEIS - IDA8424© 2012 ATEÏS6. Now look at the Over/Under red LED:If both Over/Under LEDs are OFF, it means the calibration has properly finished and t
Components of Audio Processor 425© 2012 ATEÏSDo not adjust the gain of output, amplifier or sensing microphone during or after thecalibr
ATEIS - IDA8426© 2012 ATEÏSAs the noise level is nearer than during the calibration, the differential level is almost null. You cansee the AGC level i
Components of Audio Processor 427© 2012 ATEÏSIf the sensing microphone detects more noise than during the calibration, the A.N.G. works in the"
ATEIS - IDA8428© 2012 ATEÏSComponent Appearance:Description:A Compressor is an automatic volume control. Loud sounds over a certain threshold are redu
Components of Audio Processor 429© 2012 ATEÏSEnables/disables the “Soft Knee” mode. This element controls whether the bend in the responsecurve is a s
Product Features 43© 2012 ATEÏSDown Button: To Navigate menu of touch screen.Plus Button: To Navigate menu of touch screen.Down Button: To Navigate me
ATEIS - IDA8430© 2012 ATEÏSRelease Time:Sets the time it takes to release the gain reduction. The 'release phase' is the period when thecomp
Components of Audio Processor 431© 2012 ATEÏSo Y: Output signal level(dB)Control Pointso Blue: Adjusts Threshold.o Red: Adjusts Threshold Range.o Yell
ATEIS - IDA8432© 2012 ATEÏS Comp-limiter is a combination of the Compressor and the Limiter Components.Control WindowElement PropertiesNameInitialMin
Components of Audio Processor 433© 2012 ATEÏSHard Clipping(Limiter):Enables/disables the “Hard clipping” mode.Threshold(Limiter):Sets the threshold le
ATEIS - IDA8434© 2012 ATEÏSAxiso X: Input signal level (dB)o Y: Output signal level (dB)Control Pointso Blue: Adjusts Threshold(Compressor).o Red: Adj
Components of Audio Processor 435© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitMin Gain-6.0-15.000.1dBMax Gain6.0015.00.1dBSamp
ATEIS - IDA8436© 2012 ATEÏSElement Description:Min Gain:The minimum AGC level compensation.Max Gain:The maximum AGC level compensation.Sampling Time:D
Components of Audio Processor 437© 2012 ATEÏSIndicates that the AGC gain is decreasing.Dead Zone:Indicates that the AGC is not changing.Increase Zone:
ATEIS - IDA8438© 2012 ATEÏS6.4.6 Ducker\Ducker StereoComponent TemplateComponent Appearance:Description:The Ducker is a type of "sophisticated sw
Components of Audio Processor 439© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitBypassOff----ActiveOff----Thd.-20.0-80.035.00.1dBResponse Time10010
ATEIS - IDA844© 2012 ATEÏS System Setting:There are 5 pages in the system setting menu.
ATEIS - IDA8440© 2012 ATEÏSFor example, we set a system for a speech with background music playing and the speechmaker isusing a standard dynamic
Components of Audio Processor 441© 2012 ATEÏS6.4.7 Expander\Expander StereoComponent Template:Component Appearance:Description:An expander works in an
ATEIS - IDA8442© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----Soft KneeOn----ExpandOff----Ratio2.01.020.00.1x;1Thre
Components of Audio Processor 443© 2012 ATEÏSRelease Time:Adjusts the time to stop the gain reduction.Gain Reduction:Reflects the current amount of ga
ATEIS - IDA8444© 2012 ATEÏS6.4.8 Gate6.4.8.1 Gate - MonoComponent TemplateComponent Appearance:Description:The Gate allows you to cut off the signal b
Components of Audio Processor 445© 2012 ATEÏSControl Window:Element Properties:NameInitialMinimumMaximumPrecisionUnitMuteOff----BypassOff----Gate OnOf
ATEIS - IDA8446© 2012 ATEÏSAdjusts the time between the level's detection and the beginning of the Gate operation.Attack Time:Adjusts the fade-in
Components of Audio Processor 447© 2012 ATEÏSDescription:Simple double channel Gate.Control Window:Element Properties:NameInitialMinimumMaximumPrecisi
ATEIS - IDA8448© 2012 ATEÏSSets the volume of the signal connected in the input R.Thd.:Sets the threshold level above which the Gate will open.Respons
Components of Audio Processor 449© 2012 ATEÏS6.4.8.3 Gate - VoiceComponent Template:Component Appearance:Description:This component is the Gate-Voice
Product Features 45© 2012 ATEÏS
ATEIS - IDA8450© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitGate OnOff----MuteOff----BypassOff----Thd.-20.0-90.035.00.1dBHold
Components of Audio Processor 451© 2012 ATEÏSVoice Recognition:The level of sensitivity for human voice.6.4.8.4 Gate with SidechainComponent Template:
ATEIS - IDA8452© 2012 ATEÏSControl Window:Element Properties:NameInitialMinimumMaximumPrecisionUnitMuteOff----BypassOff----Gate OnOff----Sidechain Gai
Components of Audio Processor 453© 2012 ATEÏSSets the volume of the signal connected in the input S.Input Gain:Sets the volume of the signal connected
ATEIS - IDA8454© 2012 ATEÏS6.4.9 Limiter\Limiter StereoComponent Template:Component Appearance:Description:This component limits the audio level depen
Components of Audio Processor 455© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----Hard ClippingOn----LimitingOff----T
ATEIS - IDA8456© 2012 ATEÏSLimiting:Indicates the limiting.Threshold:Sets the threshold level above which limiting begins.Release Time:Sets the time i
Components of Audio Processor 457© 2012 ATEÏSo Y: Output signal level(dB)Control Points:o Red: Adjusts Threshold.6.5 Equalizer6.5.1 GEQ\GEQ StereoComp
ATEIS - IDA8458© 2012 ATEÏSDescriptionGEQ is the abbreviation of Graphic Equalizer. In the Graphic Equalizer the input signal is sent to abank of fil
Components of Audio Processor 459© 2012 ATEÏSAxis:o X: Frequency of output signal(Hz)o Y: Gain of output signal(dB)Control Points:o Blue: Adjusts Gain
ATEIS - IDA846© 2012 ATEÏS4.1.1.7.1 PagingHere you can select the zone and paging.After the editing of Front Panel Paging (Fireman, Message play and
ATEIS - IDA8460© 2012 ATEÏS6.5.2 PEQ\PEQ StereoComponent Template:Component Appearance:Description:PEQ is the abbreviation of Parametric Equalizer.
Components of Audio Processor 461© 2012 ATEÏScan be widened or narrowed. PEQs are capable of making much more precise adjustments to soundthan other e
ATEIS - IDA8462© 2012 ATEÏSSets the frequency of a band.Gain:Sets the gain (attenuate or increase the selected frequency).Graphical Control Window:Axi
Components of Audio Processor 463© 2012 ATEÏS6.6 FeedbackComponent Template:Component Appearance:Description:The error between the desired and the act
ATEIS - IDA8464© 2012 ATEÏSdetects feedback and attenuates the responsible frequency. There is several types of feedbackcomponents. The di
Components of Audio Processor 465© 2012 ATEÏSElement Description:Bypass:Bypasses the feedback’s module. By clicking on the Bypass button you will eras
ATEIS - IDA8466© 2012 ATEÏSStop Detect:Stops detecting feedback.Reset All:Resets all coefficients.Detect Level:The level of feedback detection.Depth:T
Components of Audio Processor 467© 2012 ATEÏSElement Properties:Generate Information:NameInitialMinimumMaximumPrecisionUnitBypass AllOff----BypassOn--
ATEIS - IDA8468© 2012 ATEÏSAxis:o X: Frequency of output signal(Hz)o Y: Gain of output signal(dB)Control Points:o Blue: Adjusts Frequencyo Yellow: Adj
Components of Audio Processor 469© 2012 ATEÏSDescription:A Band Pass component that passes frequencies within a certain range and rejects (attenu
Product Features 47© 2012 ATEÏSThe ID(1 ,1) here means the first device in the first IDA8 system. Generally, the master unit would be(n, 1), and slave
ATEIS - IDA8470© 2012 ATEÏSThe type of filtering, Slope:Slopes of attenuation.Bandwidth:Difference between the upper and lower frequencies in a contig
Components of Audio Processor 471© 2012 ATEÏS6.7.3 Band StopComponent Template:Component Appearance:Description:A Band Stop filter is a filter that
ATEIS - IDA8472© 2012 ATEÏSGenerate Information:NameInitialMinimumMaximumPrecisionUnitModeButterworth----Slope12dB----Bandwidth1.000.012.000.01OctaveB
Components of Audio Processor 473© 2012 ATEÏSAxis:o X: Frequency of output signal(Hz)o Y: Level of input signal(dB)Control Points:o Blue: Adjust eleme
ATEIS - IDA8474© 2012 ATEÏS6.7.4 Crossover/Crossover StereoComponent Template:Component Appearance:Description:Crossovers split the audio signal into
Components of Audio Processor 475© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitInvert-----Mode-----Slope-----Mute-----Level----
ATEIS - IDA8476© 2012 ATEÏSInverts the phase of the signal.Mode:The type of filtering.Slope:The slope of attenuation.Mute:Mutes the filter's modu
Components of Audio Processor 477© 2012 ATEÏS6.7.5 Hi/Lo PassComponent Template:Component Appearance:Description:Hi/Lo Pass component passes high/low
ATEIS - IDA8478© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitModeBessel 6 dB----TypeLow-Pass----BypassOff----MuteOff----Level0-90.020.00.1dBFreque
Components of Audio Processor 479© 2012 ATEÏSo X: Frequency of output signal(Hz)o Y: Level of input signal(dB)Control Points:o Red: Adjust element Fre
ATEIS - IDA848© 2012 ATEÏSTemperature:Folder CRC:VER.: The last time of modification.Folder name: Here displays the items in machine file system, see
ATEIS - IDA8480© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitModeButterworth----Slope12dB----Bandwidth10.012.000.01OctaveBypass
Components of Audio Processor 481© 2012 ATEÏSAxis:o X: Frequency of output signal(Hz).o Y: Level of input signal(dB).Control Points:o Blue: Adjust ele
ATEIS - IDA8482© 2012 ATEÏS6.7.7 Shelving FilterComponent Template:Component Appearance:Description:Shelving Filter component implements a first order
Components of Audio Processor 483© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitBypassOff----Level0-90.020.00.1dBFrequency100010220001HzElement Des
ATEIS - IDA8484© 2012 ATEÏS6.8 FiremanComponent Template:Component Appearance:Description:This component represents the Fireman Microphone with one ch
Components of Audio Processor 485© 2012 ATEÏSThe signal level of the Fireman component. Paging-Event Selection:Selects a paging event to bind with the
ATEIS - IDA8486© 2012 ATEÏSDescription:This component controls the input signal's parameters and monitors it. The analog input modulesrepres
Components of Audio Processor 487© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitOverload Thd.0-20.020.00.1dBElement Description:Bypass:Bypasses aud
ATEIS - IDA8488© 2012 ATEÏS6.9.2 Mono InputComponent Template:Component Appearance:Description:For the AES/EBU input, the elements inside the componen
Components of Audio Processor 489© 2012 ATEÏSElement Properties: NameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff--
Product Features 49© 2012 ATEÏSCRC: The number here is between 0 to 65535, write down the unicode for check if the files aremodified or not.4.1.1.7.3
ATEIS - IDA8490© 2012 ATEÏSThis LED lights up if the signal of an input channel is greater than the Overload Thd.Volume:The VU-Meter shows the channel
Components of Audio Processor 491© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff---
ATEIS - IDA8492© 2012 ATEÏSThis LED lights up if the signal of an input channel is greater than the Overload Thd.Volume:The VU-Meter shows the channel
Components of Audio Processor 493© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff---
ATEIS - IDA8494© 2012 ATEÏSThis LED lights up if the signal of an input channel is greater than the Overload Thd.Volume:The VU-Meter shows the channel
Components of Audio Processor 495© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitMuteOff----InvertOff----Element Description:Mute
ATEIS - IDA8496© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----Input Level0-90.020.00.1dBOutput Level0-90
Components of Audio Processor 497© 2012 ATEÏS6.11 Local Echo SuppressorComponent Template:Component Appearance:Description:This component is design
ATEIS - IDA8498© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----Gain Reduction0-25.000.1dBPre-Processing Threshold-22
Components of Audio Processor 499© 2012 ATEÏSPost-Processing Threshold:When the input volume is smaller than the Post-Processing Threshold, it
5Contents5© 2012 ATEÏS...
ATEIS - IDA850© 2012 ATEÏSIf the leakage value is too low, the fault list displays AMP Zone n Leakage (n=1~8).Normal/Backup AMP Monitoring:Here displa
ATEIS - IDA8500© 2012 ATEÏS6.12.2 EVAC BoardComponent Template:Component Appearance:Description:This component corresponds to URGP peripheral dev
Components of Audio Processor 501© 2012 ATEÏSType:To specify the mode of activation. There are two choices:o N.O.:Normally open, close the contact to
ATEIS - IDA8502© 2012 ATEÏS6.12.3 Evacuation InputComponent Template:Component Appearance:Description:This component corresponds to the Evacuation Inp
Components of Audio Processor 503© 2012 ATEÏSParameters:Monitor Mode:There are two options:o Voltage: The logic output of component which is triggered
ATEIS - IDA8504© 2012 ATEÏS6.12.4.1 TriggerComponent Template:Component Appearance:Description:This component links events to the logic signal. The li
Components of Audio Processor 505© 2012 ATEÏSAfter events are linked to the component the control window lists them in grids:Parameters:Event Name:Sho
ATEIS - IDA8506© 2012 ATEÏSIn the above figure, the logic output channel 4 and 6 are selected. For more settings, click thegrid cell [...]:In the abov
Components of Audio Processor 507© 2012 ATEÏSDescription:This component allows the user to generate the logic signal using buttons in the software. Fo
ATEIS - IDA8508© 2012 ATEÏS6.12.7 Logic Net InputComponent Template:Component Appearance:Description:This component transfers logic signals over Ateis
Components of Audio Processor 509© 2012 ATEÏS6.12.8 Logic Net OutputComponent Template:Component Appearance:Description:This component transfers logic
Product Features 51© 2012 ATEÏSo 1K tone: Press to check the 1K tone.o Reset Monitor: Stop monitoring.Data/Time:Here you can set the current time, cha
ATEIS - IDA8510© 2012 ATEÏS6.12.9 NOTComponent Template:Component Appearance:Description:This component performs logical NOT operation.6.12.10 ORCompo
Components of Audio Processor 511© 2012 ATEÏSComponent Appearance:Description:This component performs logical OR operation.6.12.11 OutputComponent Tem
ATEIS - IDA8512© 2012 ATEÏS6.12.12 SchedulerComponent Template:Component Appearance:Description:This component allows the user to arrange the timin
Components of Audio Processor 513© 2012 ATEÏSScheduler List:At the left side of the window, a box lists all channels of the scheduler. Click it to cha
ATEIS - IDA8514© 2012 ATEÏSSpecifies the condition to deactivate a scheduler. There are three types of stop condition:Continue:In this option, schedul
Components of Audio Processor 515© 2012 ATEÏSThe Occurrence parameter determines the cycle type of triggering. There are five typesavailab
ATEIS - IDA8516© 2012 ATEÏS6.13 Meter6.13.1 Peak/RMS MeterComponent Template:Component Appearance:Description:This component displays the amplitude
Components of Audio Processor 517© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitIndefiniteOff----Measure TypeRMS----Hold Time101
ATEIS - IDA8518© 2012 ATEÏS6.14 Message6.14.1 Message PlayerComponent Template:Component Appearance: Description:This component plays the audio messag
Components of Audio Processor 519© 2012 ATEÏSCR Pin: Clear. This will cancel the event for triggering messages and clear all of the logicsignal
ATEIS - IDA852© 2012 ATEÏSSource Status: Here displays the audio source you choose.VOL: Adjust the volume of the speakers.Paging Reset:Cancel all pagi
ATEIS - IDA8520© 2012 ATEÏSMessages: The total messages in this event.Add an event by clicking "..." in the Messages column to open the
Components of Audio Processor 521© 2012 ATEÏSSet the logic out signal:1. Interrupt: If the IR trigger interrupts the Event 1, the logic output C
ATEIS - IDA8522© 2012 ATEÏS3. Playing: When the first message (gong.wav) is playing, logic output Ch1 will send a signal"High".4. Idle:
Components of Audio Processor 523© 2012 ATEÏSo Interrupt Enable:When interrupt is enabled, it means that except for the "Nth times"
ATEIS - IDA8524© 2012 ATEÏS 6.14.2 MM PlayerComponent Template:Component Appearance:
Components of Audio Processor 525© 2012 ATEÏSDescription:This component plays the messages stored in the Ateis device. It allows the user to specify p
ATEIS - IDA8526© 2012 ATEÏSYou can set the Message play list, in this window:Mode: o Logic Input: Choose Logic IN1~ IN8 to control when your message
Components of Audio Processor 527© 2012 ATEÏSHere is an example for explaining the order of play with Dynamic.Once the Logic IN 1 is high, it
ATEIS - IDA8528© 2012 ATEÏS6.15 Mixer6.15.1 AutoMixerComponent Template:Component Appearance:Description:This component mixes several signals to one o
Components of Audio Processor 529© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitTypeManual----Last Mic. On DesignatedChannel 1--
Product Features 53© 2012 ATEÏS4.1.2 IDA8SAB4.1.2.1 OverviewThe IDA8SAB Slave units provide audio-in and output expansion of the IDA8 Systems using a
ATEIS - IDA8530© 2012 ATEÏSManual mode: The user manually activates channels (the threshold and priority are ignored).Automatic mode: Channels activat
Components of Audio Processor 531© 2012 ATEÏSattenuation when a channel is added or removed.NOM Attenuation Step:Sets the amount of attenuation applie
ATEIS - IDA8532© 2012 ATEÏSThis component allows mixing several signals to one output. The activation of channel(s) can bedone manually or autom
Components of Audio Processor 533© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitMatrix Output MuteOff----Matrix Output Level0-90.000.1dBOutput Leve
ATEIS - IDA8534© 2012 ATEÏSMutes or unmutes the module's output. Matrix Output Mute:Mutes an input for the output mixing. Different than the Mute
Components of Audio Processor 535© 2012 ATEÏS6.15.3 MatrixComponent Template:Component Appearance:Description:The Matrix Mixer offers two main functio
ATEIS - IDA8536© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitInput MuteOff----Input Level0-60.020.00.1dBOutput Level0-60.020.00
Components of Audio Processor 537© 2012 ATEÏS6.15.4 StandardComponent Template:Component Appearance:Description:The matrix module is similar to the st
ATEIS - IDA8538© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitInput MuteOff----Input Level0-90.020.00.1dBOutput MuteOff----Outpu
Components of Audio Processor 539© 2012 ATEÏSDescription:This component transfers audio signals over Ateis Net.The signal goes into a channe
ATEIS - IDA854© 2012 ATEÏS4.1.2.2 Front Panel System Fault LED:This LED lights up when a system fault fault is detected. G.Fault LED:This LED lights u
ATEIS - IDA8540© 2012 ATEÏS6.17 Net OutputComponent Template:Component Appearance:Description:This component transfers audio signals over Ateis Net. I
Components of Audio Processor 541© 2012 ATEÏS6.18 Noise Generator6.18.1 PinkComponent Template:Component Appearance:Description:Pink noise or 1/ƒ nois
ATEIS - IDA8542© 2012 ATEÏSMute:Mutes the sound coming out from the component.Level:The level of the pink noise.6.18.2 ToneComponent Template:Componen
Components of Audio Processor 543© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitLevel-100.0-100.020.00.1dBTone freq.100020200001
ATEIS - IDA8544© 2012 ATEÏS6.18.3 WhiteComponent Template:Component Appearance:Description:This component generates a White noise. The White noise is
Components of Audio Processor 545© 2012 ATEÏSNameInitialMinimumMaximumPrecisionUnitMute-----Level-100.0-100.020.00.1dBElement Description:MuteMutes th
ATEIS - IDA8546© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----L
Components of Audio Processor 547© 2012 ATEÏSLevel:The signal output level of the module.Overload thd.:Sets the threshold of the overload indicator. 6
ATEIS - IDA8548© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----L
Components of Audio Processor 549© 2012 ATEÏSLevel:The signal output level of the module.Overload thd.:Sets the threshold of the overload indicator. 6
Product Features 55© 2012 ATEÏSLine B ErrorBackup AMP ErrorAMP Line Leakage Error4.1.2.3 Rear Panel Speaker Zone Outputs:There are 8 zones for speaker
ATEIS - IDA8550© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----L
Components of Audio Processor 551© 2012 ATEÏSLevel:The signal output level of the module.Overload thd.:Sets the threshold of the overload indicator. 6
ATEIS - IDA8552© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----L
Components of Audio Processor 553© 2012 ATEÏSLevel:The signal output level of the module.Overload thd.:Sets the threshold of the overload indicator. 6
ATEIS - IDA8554© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-50.0-50.020.00.1dBuMuteOff----SignalOff----L
Components of Audio Processor 555© 2012 ATEÏSLevel:The signal output level of the module.Overload thd.:Sets the threshold of the overload indicator. 6
ATEIS - IDA8556© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitActivationFixed----TTL InOff----Priority*1----Gate OnOff----SoloOf
Components of Audio Processor 557© 2012 ATEÏSLights up when the gate is activated (open).Solo:Only routes this input.Busy:Lights up if the gate of the
ATEIS - IDA8558© 2012 ATEÏSDescription:The Network Paging component routes the input source signal to zones using priority arbitration.The pins a
Components of Audio Processor 559© 2012 ATEÏSA source type is an identification for paging activities. If a zone is occupied by some source forpa
ATEIS - IDA856© 2012 ATEÏSOptional card to build a local dedicated IDA8C-IDA8S network. Configurable Audio I/Os:Two configurable 0dB audio I/O port A
ATEIS - IDA8560© 2012 ATEÏSEvac:Enable this option to set the paging source as an evacuation source. If an evacuation source isactivated on paging, An
Components of Audio Processor 561© 2012 ATEÏSThere are various modes for triggering a paging activity.o None:The paging request is not coming from the
ATEIS - IDA8562© 2012 ATEÏSo Logic Signal:A paging request of the channel is established depending on the logic signal of an input.Basically, if a log
Components of Audio Processor 563© 2012 ATEÏSCode:A code is a zone combination so called a selection of zones. The figure above is anexample, the zo
ATEIS - IDA8564© 2012 ATEÏSButton Add:Add codes to event.Button Remove:Remove selected code.o SingularThis event is similar to the integration paging
Components of Audio Processor 565© 2012 ATEÏSthe paging succeeds. On the opposite side, the paging request is denied. The available zonesmeans the bei
ATEIS - IDA8566© 2012 ATEÏSThere 20 channel logic outputs for each Network Paging component. This section shows theconfiguration about it
Components of Audio Processor 567© 2012 ATEÏSIt is able to output a logical High to a specific output channel in condition of a zone is occupied by as
ATEIS - IDA8568© 2012 ATEÏS6.21 RS485 Audio6.21.1 RS485 InputComponent Template:Component Appearance:Description:This component controls and monito
Components of Audio Processor 569© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitBypassOff----MuteOff----RTOOff----OverloadOff---
Product Features 57© 2012 ATEÏSMaximum level = 14 dBOutput Impedance = 50 OhmTHD+N(Total Harmonic Distortion plus Noise)SensitivityMinimumMaximumUnitF
ATEIS - IDA8570© 2012 ATEÏSThis LED lights up if the signal of the input channel is greater than the Overload Thd.Volume:The VU-Meter shows the channe
Components of Audio Processor 571© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitOverloadOff----Volume-20.0-20.020.00.1dBMuteOff-
ATEIS - IDA8572© 2012 ATEÏSLevel:The signal output level of the channel.Overload Thd.:A threshold value to determine if the signal of a channel is ove
Components of Audio Processor 573© 2012 ATEÏSElement Description:Input Select:Open the drop-down list to select the input.6.23 Signal MonitorComponent
ATEIS - IDA8574© 2012 ATEÏSElement Properties:NameInitialMinimumMaximumPrecisionUnitTrigger OnOff----Threshold-20.0-50.020.00.1dBVolume-40.0-40.020.00
Components of Audio Processor 575© 2012 ATEÏS6.24 Telephone Card6.24.1 TC TransmitComponent Template:Component Appearance:Description:This component
ATEIS - IDA8576© 2012 ATEÏSo B: Busy statuso M: MCU statusControl Window:Element Properties:NameInitialMinimumMaximumPrecisionUnitDialingOff----Ringin
Components of Audio Processor 577© 2012 ATEÏSHangs up the telephone.Digit Keys:16 Digit Keys at the left part of the control window on the panel inclu
ATEIS - IDA8578© 2012 ATEÏSFlash:This button allows a 3-way telephone conversation. Press this button during the connection ofthe first remote phone a
Components of Audio Processor 579© 2012 ATEÏSControl Window:Element Properties:NameInitialMinimumMaximumPrecisionUnitCaller MuteOff----Caller Level0-1
ATEIS - IDA858© 2012 ATEÏSSensitivity:For each channel of a configurable audio input card, there are five levels to gain the audio signal.They are se
ATEIS - IDA8580© 2012 ATEÏSHistory:Displays the history of the DTMF numbers.Phone Answer:The mode of action for answering incoming calls. There are tw
Components of Audio Processor 581© 2012 ATEÏSThis component is a bridge between the Ateis device and the Voxnet device. It maps the key in theVoxnet p
ATEIS - IDA8582© 2012 ATEÏS7 Contact Informationhttp://www.ateis.comATEÏS Europe BVATEÏS Suisse SAAddress:Sydneystraat 423047BP ROTTERDAM, NETHERLANDS
Product Features 59© 2012 ATEÏSEvacuation Inputs(Voltage Mode):On Voltage:ItemMinimumMaximumUnitHigh1872VDCLow-0.5VDCContact Outputs + EVAC, Fault Sta
ATEIS - IDA86© 2012 ATEÏS...
ATEIS - IDA860© 2012 ATEÏSDeviceConnectionMax. NumFunctionPPM ASPDC31Remote console with paging ability.PSS ASPDC1Remote console for Paging and Event
Product Features 61© 2012 ATEÏS4.1.3 IDA8SL4.1.3.1 OverviewThe IDA8SL Slave units provide audio output expansion of the IDA8 Systems using
ATEIS - IDA862© 2012 ATEÏS4.1.3.2 Front Panel System Fault LED:This LED lights up when a system fault fault is detected. G.Fault LED:This LED lights u
Product Features 63© 2012 ATEÏSLine B ErrorBackup AMP ErrorAMP Line Leakage Error4.1.3.3 Rear Panel Backup Amplifier Output:This connector connects to
ATEIS - IDA864© 2012 ATEÏS Zone1 Amplifier Output:This connector is used to connect the output of the zone1 amplifier for receiving the 100V audio
Product Features 65© 2012 ATEÏS4.1.3.4 CharacteristicsCase:Dimension = 436mm (W) x 300mm (L) x 88mm (H)Weight = 5KgColor = RAL7016Power:ItemVoltageCur
ATEIS - IDA866© 2012 ATEÏS0dBu-0.04%20~20kHz@+4dBu-12dBu-0.06%[email protected]%[email protected]%[email protected]%20~20kHz
Product Features 67© 2012 ATEÏSTHD @ 1kHz at input < 0.02Bandwidth @ -3dB at input < 20Hz ~ 22kHzRS232 voltages = -6.5/+6.5Evacuation Inputs(Con
ATEIS - IDA868© 2012 ATEÏSContact OutputContact FormMaximumUnitCarry Current1.0ADCMaximum Voltage100VDCElectrical Life1 x 10^8 (Ref 10VDC, 10mA)-Worki
Product Features 69© 2012 ATEÏSDeviceConnectionMax. NumFunctionInputPPM ASPDC31Remote console for paging ability.PSS ASPDC1Remote console for Paging a
7Contents7© 2012 ATEÏS...
ATEIS - IDA870© 2012 ATEÏS4.1.4 IDA8S4.1.4.1 OverviewThe IDA8S Slave units provide audio in and output expansion of the IDA8 Systems using a secured 4
Product Features 71© 2012 ATEÏS System Fault LED:This LED lights up when a system fault fault is detected. G.Fault LED:This LED lights up when a globa
ATEIS - IDA872© 2012 ATEÏS4.1.4.3 Rear Panel Speaker Zone Outputs:There are 8 zones for speaker & amplifier connection. each zone consists of fol
Product Features 73© 2012 ATEÏS 24V DC Input:Main 24VDC power supply connector.4.1.4.4 CharacteristicsCase:Dimension = 436mm (W) x 285mm (L) x 44mm (H
ATEIS - IDA874© 2012 ATEÏSTHD+N(Total Harmonic Distortion plus Noise)SensitivityMinimumMaximumUnitFrequency0dBu-0.04%20~20kHz@+4dBu-12dBu-0.06%20~20kH
Product Features 75© 2012 ATEÏSMaximum Input Level = 16 dBuInput Impedance = 11k OhmTHD @ 1kHz at input < 0.02Bandwidth @ -3dB at input < 20Hz ~
ATEIS - IDA876© 2012 ATEÏSContact OutputContact FormMaximumUnitCarry Current1.0ADCMaximum Voltage100VDCElectrical Life1 x 10^8 (Ref 10VDC, 10mA)-Worki
Product Features 77© 2012 ATEÏSDeviceConnectionMax. NumFunctionInputPPM ASPDC31Remote console for paging ability.PSS ASPDC1Remote console for Paging a
ATEIS - IDA878© 2012 ATEÏSConnection example : Local Ateis Net.1 IDA8C and 2 IDA8SABs connect through Local Ateis Net:Inside the IDA8 units, the packe
Product Features 79© 2012 ATEÏSConnection example : Global / Local Ateis Net.
ATEIS - IDA88© 2012 ATEÏS...
ATEIS - IDA880© 2012 ATEÏS4.1.6 Amplifier Configuration4.1.6.1 Basic Amplifier ConnectionBasic Amplifier ConnectionThe IDA8 System applies a flexib
Product Features 81© 2012 ATEÏSBackup Amplifier Connections:The is for the connection of amplifiers for backup. In above figure(Basic Amplifier Conne
ATEIS - IDA882© 2012 ATEÏSAudio Routing without Backup AmplifierThe figure below(Audio Routing with Backup Amplifier) shows the amplifier backup in t
Product Features 83© 2012 ATEÏSamplifier can serve Zone 1 to Zone 4. The figure below shows this concept:Share the Backup AmplifierIn the above figure
ATEIS - IDA884© 2012 ATEÏSAdvance Backup Amplifier SetupThere are three backup amplifier groups in the above figure:Backup Group1:Amplifier B1 serves
Product Features 85© 2012 ATEÏSAmplifier B3 serves Zone 13 ~ zone24.Software settings for the backup amplifier:It is necessary to have software settin
ATEIS - IDA886© 2012 ATEÏSThe meaning of the parameters are listed below:Amount:Specifies the number of backup amplifiers in system. The list content
Product Features 87© 2012 ATEÏSThe G.Fault LED lights up for mostly all faults.When a fault is generated, the following will be performed by the IDA8C
ATEIS - IDA888© 2012 ATEÏSNameDescription3. Line A/B short, a circuit outside the speaker zone outputconnector is shorted, and no sound comes out. Thi
Product Features 89© 2012 ATEÏSNameDescriptionNo Preset TableThere is no configuration inside the device.SPI Flash ErrorThere is an internal error of
9Contents9© 2012 ATEÏS...
ATEIS - IDA890© 2012 ATEÏSLED Indicator:When this error is detected, the following LEDs will light up:o System Fault LED on the front panel of the IDA
Product Features 91© 2012 ATEÏSContact your technician to repair device.4.1.7.1.1.4 DSP ErrorFault Meaning:There is an internal error of communicatio
ATEIS - IDA892© 2012 ATEÏSA buzzing sound outputs to the monitoring speaker on the front panel of the IDA8C.Fault Handling:1. Update the firmware with
Product Features 93© 2012 ATEÏSo System Fault LED on the front panel of the IDA8C/S.o G. Fault LED on the front panel of the IDA8C/S.Log:Text messages
ATEIS - IDA894© 2012 ATEÏS4.1.7.1.1.9 Trans ErrorFault Meaning:There is an internal hardware error of device.Fault Indication:LED Indicator:When this
Product Features 95© 2012 ATEÏSA buzzing sound outputs to the monitoring speaker on the front panel of the IDA8C.Fault Handling:Decrease the audio lev
ATEIS - IDA896© 2012 ATEÏS4.1.7.1.1.12 Reset ErrorFault Meaning:Last time the machine is unpredictably shut down, please see the machine log.Fault In
Product Features 97© 2012 ATEÏSA buzzing sound outputs to the monitoring speaker on the front panel of the IDA8C.Fault Handling:Contact your technicia
ATEIS - IDA898© 2012 ATEÏSLog:Text messages display at the touch screen of the IDA8C:"SSI error"Text messages display at the window [Machine
Product Features 99© 2012 ATEÏSFault Indication:LED Indicator:When this error is detected, the following LEDs will light up:o G. Fault LED on the fron
Kommentare zu diesen Handbüchern